AMP-O-LECTRIC Model “G” Terminating Machines
The Model “G” is the most advanced design in the long-standing series of AMP-O-LECTRIC machines for terminating wire using reeled terminals and contacts. It features a reliable direct motor drive system. Its modular construction also enables us to provide versions for use either as bench-top units, or in combination with fully-automatic lead-making equipment.
For operator convenience, we’ve improved access to, and lighting in the target area, and moved the Crimp Quality Monitor (CQM II) to eye level for bench-top use. The Model “G” is also quieter, plus improved guarding meets applicable European and domestic safety requirements.
All Model “G” versions include precision adjustment for crimp height — an important feature, which, in combination with the optional CQM, will enable you to maintain the tight tolerances required for today’s demands for higher levels of quality. By simply resetting a dial, an operator can adjust crimp height in .0005 [0.013] increments over a .018 [0.457] range.
Another user-friendly feature is its control system. At the push of a button, you can power the motor on or off, jog forward or reverse, switch to split-cycle operation, turn the work light off or on, power the air feed on or off, or reset the batch counter. And, it’s all reported on an LCD display. The controls will also detect and report errors in the machine, and stop cycling when a bad crimp is detected by the CQM. The operator must then push the reset button to continue.
The Model “G” will accept all existing TE miniature applicators, with minor modifications.
Most of our existing applicators may be used for crimp quality monitoring on versions equipped with CQM and CQM G-Adapter. To use CQM for Tab-Lok, FASTON flag terminals, a CQM hinge-bar applicator is required. You can’t use CQM to monitor the application of closed-barrel pre-insulated terminals.
Fast Facts
Features:
The AMP-O-LECTRIC Model “G” Terminating Machine was designed to be used as a stand-alone semiautomatic bench machine. End-Feed and Side-Feed Miniature Applicators are easily installed and removed without repositioning the applicator mounting plate on the machine. A precision adjustment feature is included in the terminating machine to provide quick and accurate crimp height adjustments. The Model “G” Terminating Machine accepts a wide variety of miniature applicators, with minor adjustments, thus providing a great selection of terminals for many applications.
The CQM adapter adds Crimp Quality Monitoring to the Model “G” Terminating Machine.
For operator convenience, we’ve improved access to, and lighting in the target area, and moved the Crimp Quality Monitor (CQM II) to eye level for bench-top use. The Model “G” is also quieter, plus improved guarding meets applicable European and domestic safety requirements.
All Model “G” versions include precision adjustment for crimp height — an important feature, which, in combination with the optional CQM, will enable you to maintain the tight tolerances required for today’s demands for higher levels of quality. By simply resetting a dial, an operator can adjust crimp height in .0005 [0.013] increments over a .018 [0.457] range.
Another user-friendly feature is its control system. At the push of a button, you can power the motor on or off, jog forward or reverse, switch to split-cycle operation, turn the work light off or on, power the air feed on or off, or reset the batch counter. And, it’s all reported on an LCD display. The controls will also detect and report errors in the machine, and stop cycling when a bad crimp is detected by the CQM. The operator must then push the reset button to continue.
The Model “G” will accept all existing TE miniature applicators, with minor modifications.
Most of our existing applicators may be used for crimp quality monitoring on versions equipped with CQM and CQM G-Adapter. To use CQM for Tab-Lok, FASTON flag terminals, a CQM hinge-bar applicator is required. You can’t use CQM to monitor the application of closed-barrel pre-insulated terminals.
Fast Facts
- Quieter
- Improved guarding and lighting
- Toolless changeover of applicators
- Precision manual- or autoadjust for crimp height
- Total and batch counter
- Accepts all existing TE miniature applicators, with minor modifications
- Reduced maintenance requirements
- Split-cycle operation for both leadmaking and bench-top use
- Standardized 15/8 [41.3] stroke
- Cannot be operated during normal production with guards open
- Operates on either 120 or 220 VAC, 50 or 60 Hz
- Available with CQM G-Adapter for crimp quality monitoring using miniature applicators
- Produced under a Quality Management System certified to ISO 9001
Features:
- Jog Mode (Guards Open) This mode allows maintenance and setup
- Crimp Height Adjustment Feature
- Easy End-Feed/Side-Feed Conversion
- Easy Cleaning and Lubrication
- Manual Precision Crimp Height Adjustment
- Automatic Precision Crimp Height Adjustment – Auto Adjust
The AMP-O-LECTRIC Model “G” Terminating Machine was designed to be used as a stand-alone semiautomatic bench machine. End-Feed and Side-Feed Miniature Applicators are easily installed and removed without repositioning the applicator mounting plate on the machine. A precision adjustment feature is included in the terminating machine to provide quick and accurate crimp height adjustments. The Model “G” Terminating Machine accepts a wide variety of miniature applicators, with minor adjustments, thus providing a great selection of terminals for many applications.
The CQM adapter adds Crimp Quality Monitoring to the Model “G” Terminating Machine.